VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Choosing Starter Vape Kit CRP for importers
starter vape kits · vape shop owners

Choosing Starter Vape Kit CRP for importers

We work with vape shop owners who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Published 08 October 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Choosing Starter Vape Kit CRP for importers configuration from a production run, photographed before packing.
Choosing Starter Vape Kit CRP for importers configuration from a production run, photographed before packing.

Unit price versus landed cost

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

We publish a realistic band of 2.85 to 8.31 per unit for standard configurations at 240 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

Batch consistency and why it matters

12 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

For vape shop owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How we structure a first order

We source starter vape kits from a small group of factories we have worked with for years. That means a specification can be held across repeat orders instead of being re-qualified from scratch every quarter. Consistency is a boring selling point and it is also the entire game.

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

  • Consolidated or split shipping, quoted both ways
  • Specification locked in writing before production starts
  • Private label files archived for future rebrands
  • Reference sample retained from every batch
  • Mixed SKU cartons to spread first-order risk
  • Document pack prepared per destination market

The reorder is the real test

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

Reorders are the real test of a supplier. If the second shipment does not match the first, the relationship is over regardless of price, so we treat the reorder as the actual deliverable.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance1.2 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order50 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

How long does production take?

Around 22 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us