VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit coil fit explained guide
starter vape kits · vape shop owners

Starter Vape Kit coil fit explained guide

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for vape shop owners.

Published 03 December 2025  ·  VapeWholesaleHub  ·  Reading time 7 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.

The checks behind every shipment

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Shipping without surprises

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 12 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

For vape shop owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Reading a quotation properly

We publish a realistic band of 2.89 to 8.51 per unit for standard configurations at 200 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

A landed cost sheet for starter vape kit has five lines: unit price, packaging, freight, duty and the cost of defects. Quoting only the first line is how buyers end up surprised at the fourth.

  • Document pack prepared per destination market
  • Seven-day defect reporting with replace-or-credit
  • Mixed SKU cartons to spread first-order risk
  • Specification locked in writing before production starts
  • Private label files archived for future rebrands
  • Artwork proof plus physical dummy for custom packaging

Presentation that earns the step-up

Counter space is finite. Three well-chosen SKUs outsell nine crowded ones, and the empty space signals a curated range rather than a clearance table.

Seasonality in starter vape kits is real but smaller than most buyers assume. The bigger swing comes from restocking discipline, not from calendar events.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance1.0 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order300 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 200 units. We would rather you handle the sample than approve a specification from a photograph.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us